View LTC3890_8980075.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ltc3858-2 1 38582f typical application features applications description low i q , dual 2-phase synchronous step-down controller high efficiency dual 8.5v/3.3v step-down converter n low operating i q : 170a (one channel on) n wide output voltage range: 0.8v v out 24v n wide v in range: 4v to 38v n r sense or dcr current sensing n out-of-phase controllers reduce required input capacitance and power supply induced noise n opti-loop ? compensation minimizes c out n phase-lockable frequency (75khz-850khz) n programmable fixed frequency (50khz-900khz) n selectable continuous, pulse-skipping or burst mode ? operation at light loads n very low dropout operation: 99% duty cycle n adjustable output voltage soft-start or tracking n power good output voltage monitor n low shutdown i q : 8a n internal ldo powers gate drive from v in or extv cc n no current foldback during start-up n 5mm 5mm qfn package n automotive systems n battery operated digital devices n distributed dc power systems efficiency and power loss vs load current the ltc ? 3858-2 is a high performance dual step-down switching regulator controller that drives all n-channel synchronous power mosfet stages. a constant frequency current mode architecture allows a phase-lockable fre- quency of up to 850khz. power loss and noise due to the input capacitor esr are minimized by operating the two controller outputs out of phase. the 170a no-load quiescent current extends operating life in battery-powered systems. opti-loop compensa- tion allows the transient response to be optimized over a wide range of output capacitance and esr values. the ltc3858-2 differs from the ltc3858 by having the overvolt- age protection crowbar and short-circuit latchoff disabled. a wide 4v to 38v input supply range encompasses a wide range of intermediate bus voltages and battery chemistries. independent soft-start pins for each controller ramp the output voltages during start-up. current foldback limits mosfet heat dissipation during short-circuit conditions. l , lt, ltc, ltm, burst mode, opti-loop , module, polyphase, linear technology and the linear logo are registered trademarks and no r sense and ultrafast are trademarks of linear technology corporation. all other trademarks are the property of their respective owners. protected by u.s. patents, including 5481178, 5705919, 5929620, 6100678, 6144194, 6177787, 6304066, 6580258. output current (a) 0.0001 40 efficiency (%) power loss (mw) 50 60 70 80 0.001 0.01 0.1 1 10 38582 ta01b 30 20 10 0 90 100 10 100 1000 1 0.1 10000 efficiency power loss v in = 12v v out = 3.3v figure 13 circuit 0.1f 62.5k 3.3h 680pf 150f 4.7f 22f 50v 0.007 20k 15k v out1 3.3v 5a 150f 0.1f 193k 7.2h 680pf 0.01 20k 15k v out2 8.5v 3.5a tg1 tg2 boost1 boost2 sw1 sw2 bg1 bg2 sgnd pgnd sense1 + sense2 + sense1 C sense2 C v fb1 v fb2 i th1 i th2 v in intv cc ss1 ss2 v in 9v to 38v 38582 ta01a 0.1f 0.1f ltc3858-2
ltc3858-2 2 38582f pin configuration absolute maximum ratings (note 1) 32 31 30 29 28 27 26 25 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 8 7 6 5 4 3 2 1 top view sense1 C freq phasmd clkout pllin/mode sgnd run1 run2 boost1 bg1 v in pgnd extv cc intv cc bg2 boost2 sense1 + v fb1 i th1 ss1 i lim pgood1 tg1 sw1 sense2 C sense2 + v fb2 i th2 ss2 pgood2 tg2 sw2 uh package 32-lead (5mm s 5mm) plastic qfn 33 sgnd t jmax = 125c, ja = 34c/w exposed pad (pin 33) is sgnd, must be soldered to pcb order information lead free finish tape and reel part marking* package description temperature range ltc3858euh-2#pbf ltc3858euh-2#trpbf 38582 32-lead (5mm 5mm) plastic qfn C40c to 125c ltc3858iuh-2#pbf ltc3858iuh-2#trpbf 38582 32-lead (5mm 5mm) plastic qfn C40c to 125c consult ltc marketing for parts specified with wider operating temperature ranges. *the temperature grade is identified by a la bel on the shipping container. consult ltc marketing for information on non-standard lead based finish parts. for more information on lead free part marking, go to: http://www.linear.com/leadfree/ for more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ input supply voltage (v in ) ......................... C0.3v to 40v topside driver voltages boost1, boost2 ................................. C0.3v to 46v switch voltage (sw1, sw2) ......................... C5v to 40v (boost1-sw1), (boost2-sw2) ................ C0.3v to 6v run1, run2 ............................................... C0.3v to 8v maximum current sourced into pin from source >8v ..............................................100a sense1 + , sense2 + , sense1 C sense2 C voltages ..................................... C0.3v to 28v pllin/mode voltage ................................... C0.3v to 6v i lim , phasmd, freq voltages ............. C0.3v to intv cc extv cc ..................................................... C0.3v to 14v i th1 , i th2 ,v fb1 , v fb2 voltages....................... C0.3v to 6v pgood1, pgood2 voltages ....................... C0.3v to 6v ss1, ss2, intv cc voltages ......................... C0.3v to 6v operating junction temperature range (note 2) .................................................. C40c to 125c maximum junction temperature (note 3) ............ 125c storage temperature range .................. C65c to 150c electrical characteristics symbol parameter conditions min typ max units v in input supply operating voltage range 438v v fb1,2 regulated feedback voltage (note 4) i th1,2 = 1.2v C40c to 125c C40c to 85c l 0.788 0.792 0.800 0.800 0.812 0.808 v v i fb1,2 feedback current (note 4) 5 50 na v reflnreg reference voltage line regulation (note 4) v in = 4.5v to 38v 0.002 0.02 %/v the l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at t a = 25c (note 2). v in = 12v, v run1,2 = 5v, extv cc = 0v unless otherwise noted.
ltc3858-2 3 38582f symbol parameter conditions min typ max units v loadreg output voltage load regulation (note 4) measured in servo loop, i th voltage = 1.2v to 0.7v l 0.01 0.1 % (note 4) measured in servo loop, i th voltage = 1.2v to 2v l C0.01 C0.1 % g m1,2 transconductance amplifier g m (note 4) i th1,2 = 1.2v, sink/source = 5a 2 mmho i q input dc supply current (note 5) pulse-skipping or forced continuous mode (one channel on) run1 = 5v and run2 = 0v, v fb1 = 0.83v (no load) or run1 = 0v and run2 = 5v, v fb2 = 0.83v (no load) 1.3 ma pulse-skipping or forced continuous mode (both channels on) run1,2 = 5v, v fb1,2 = 0.83v (no load) 2 ma sleep mode (one channel on) run1 = 5v and run2 = 0v, v fb1 = 0.83v (no load) or run1 = 0v and run2 = 5v, v fb2 = 0.83v (no load) 170 250 a sleep mode (both channels on) run1,2 = 5v, v fb1,2 = 0.83v (no load) 300 450 a shutdown run1,2 = 0v 8 20 a uvlo undervoltage lockout intv cc ramping up intv cc ramping down l l 3.6 4.0 3.8 4.2 4 v v v ovl feedback overvoltage protection measured at v fb1,2 , relative to regulated v fb1,2 71013 % i sense + sense + pins current each channel 1 a i sense C sense C pins current each channel v out1,2 < intv cc C 0.5v v out1,2 > intv cc + 0.5v 550 1 a a df max maximum duty factor in dropout, freq = 0v 98 99 % i ss1,2 soft-start charge current v ss1,2 = 0v 0.7 1.0 1.4 a v run1,2 on run pin on threshold voltage v run1 , v run2 rising l 1.21 1.26 1.31 v v run1,2 hyst run pin hysteresis voltage 50 mv v sense(max) maximum current sense threshold voltage v fb1,2 = 0.7v, v sense1 C, 2 C = 3.3v, i lim = 0 v fb1,2 = 0.7v, v sense1 C, 2 C = 3.3v, i lim = float v fb1,2 = 0.7v, v sense1 C, 2 C = 3.3v, i lim = intv cc l l l 22 43 64 30 50 75 36 57 86 mv mv mv gate driver tg1,2 pull-up on-resistance pull-down on-resistance 2.5 1.5 bg1,2 pull-up on-resistance pull-down on-resistance 2.4 1.1 tg1,2 t r tg1,2 t f tg transition time: rise time fall time (note 6) c load = 3300pf c load = 3300pf 25 16 ns ns bg1,2 t r bg1,2 t f bg transition time: rise time fall time (note 6) c load = 3300pf c load = 3300pf 28 13 ns ns tg/bg t 1d top gate off to bottom gate on delay synchronous switch-on delay time c load = 3300pf each driver 30 ns bg/tg t 1d bottom gate off to top gate on delay top switch-on delay time c load = 3300pf each driver 30 ns t on(min) minimum on-time (note 7) 95 ns electrical characteristics the l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at t a = 25c (note 2). v in = 12v, v run1,2 = 5v, extv cc = 0v unless otherwise noted.
ltc3858-2 4 38582f electrical characteristics the l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at t a = 25c (note 2). v in = 12v, v run1,2 = 5v, extv cc = 0v unless otherwise noted. symbol parameter conditions min typ max units intv cc linear regulator v intvccvin internal v cc voltage 6v < v in < 38v, v extvcc = 0v 4.85 5.1 5.35 v v ldovin intv cc load regulation i cc = 0ma to 50ma, v extvcc = 0v 0.7 1.1 % v intvccext internal v cc voltage 6v < v extvcc < 13v 4.85 5.1 5.35 v v ldoext intv cc load regulation i cc = 0ma to 50ma, v extvcc = 8.5v 0.6 1.1 % v extvcc extv cc switchover voltage extv cc ramping positive 4.5 4.7 4.9 v v ldohys extv cc hysteresis voltage 250 mv oscillator and phase-locked loop f 25k programmable frequency r freq = 25k, pllin/mode = dc voltage 105 khz f 65k programmable frequency r freq = 65k, pllin/mode = dc voltage 375 440 505 khz f 105k programmable frequency r freq = 105k, pllin/mode = dc voltage 835 khz f low low fixed frequency v freq = 0v, pllin/mode = dc voltage 320 350 380 khz f high high fixed frequency v freq = intv cc , pllin/mode = dc voltage 485 535 585 khz f sync synchronizable frequency pllin/mode = external clock l 75 850 khz pgood1 and pgood2 outputs v pgl pgood voltage low i pgood = 2ma 0.2 0.4 v i pgood pgood leakage current v pgood = 5v 1 a v pg pgood trip level v fb with respect to set regulated voltage v fb ramping negative hysteresis C13 C10 2.5 C7 % % v fb with respect to set regulated voltage v fb ramping positive hysteresis 710 2.5 13 % % t pg delay for reporting a fault (pgood low) 25 s note 1: stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. exposure to any absolute maximum ratings for extended periods may affect device reliability and lifetime. note 2: the ltc3858-2 is tested under pulsed load conditions such that t j t a . the ltc3858e-2 is guaranteed to meet performance specifications from 0c to 85c. specifications over the C40c to 125c operating junction temperature range are assured by design, characterization and correlation with statistical process controls. the ltc3858i-2 is guaranteed over the full C40c to 125c operating junction temperature range. note that the maximum ambient temperature is determined by specific operating conditions in conjunction with board layout, the rated package thermal resistance and other environmental factors. note 3: t j is calculated from the ambient temperature t a and power dissipation p d according to the following formula: t j = t a + (p d ? 34c/w) note 4: the ltc3858-2 is tested in a feedback loop that servos v ith1,2 to a specified voltage and measures the resultant v fb1,2 . the specification at 85c is not tested in production. this specification is assured by design, characterization and correlation to production testing at 125c. note 5: dynamic supply current is higher due to the gate charge being delivered at the switching frequency. see the applications information section. note 6: rise and fall times are measured using 10% and 90% levels. delay times are measured using 50% levels note 7: the minimum on-time condition is specified for an inductor peak-to-peak ripple current of 40% i max (see minimum on-time considerations in the applications information section).
ltc3858-2 5 38582f typical performance characteristics efficiency and power loss vs output current efficiency vs output current load step (burst mode operation) load step (forced continuous mode) load step (pulse-skipping mode) inductor current at light load soft-start efficiency vs input voltage output current (a) 0.0001 40 efficiency (%) 50 60 70 80 0.001 0.01 0.1 1 10 38582 g02 30 20 10 0 90 100 v in = 5v v in = 12v v out = 3.3v figure 13 circuit input voltage (v) 0 efficiency (%) 90 92 94 40 38582 g03 88 86 84 80 10 20 30 5 15 25 35 82 98 96 figure 13 circuit v out = 3.3v i out = 4a output current (a) 0.0001 40 efficiency (%) power loss (mw) 50 60 70 80 0.001 0.01 0.1 1 10 38582 g01 30 20 10 0 90 100 10 100 1000 1 0.1 10000 figure 13 circuit v in = 12v v out = 3.3v burst mode operation pulse- skipping mode forced continuous mode v out 100mv/div ac- coupled i l 2a/div 20s/div 38582 g04 v out = 3.3v figure 13 circuit v out 100mv/div ac- coupled i l 2a/div 20s/div 38585 g05 v out = 3.3v figure 13 circuit v out 100mv/div ac- coupled i l 2a/div 20s/div 38582 g06 v out = 3.3v figure 13 circuit burst mode operation 2a/div forced continuous mode pulse- skipping mode 2s/div 38582 g07 v out = 3.3v i load = 200a figure 13 circuit v out2 2v/div v out1 2v/div 20ms/div 38582 g08 figure 13 circuit tracking start-up figure 13 circuit 20ms/div v out2 2v/div v out1 2v/div 38572 g09
ltc3858-2 6 38582f typical performance characteristics total input supply current vs input voltage extv cc switchover and intv cc voltages vs temperature intv cc line regulation maximum current sense voltage vs i th voltage sense C pin input bias current maximum current sense threshold vs duty cycle foldback current limit quiescent current vs temperature shutdown current vs temperature input voltage (v) 5 supply current (a) 350 20 38582 g10 200 100 10 15 25 50 0 400 300 250 150 30 35 40 300a load figure 12 circuit v out = 3.3v one channel on no load temperature (c) C45 extv cc and intv cc voltage (v) 5.4 30 38582 g11 4.8 4.4 C20 5 55 4.2 4.0 5.6 5.2 5.0 4.6 80 105 130 intv cc extv cc rising extv cc falling v sense common mode voltage (v) 0 C600 sense C current (a) C500 C550 C450 C400 C300 C350 C200 C250 0 5 10 15 20 38582 g14 25 C50 C100 C150 feedback voltage (v) 0 0 maximum current sense voltage (mv) 10 30 40 50 0.6 90 38582 g16 20 0.3 0.1 0.7 0.4 0.2 0.8 0.5 0.9 60 70 80 i lim = intv cc i lim = float i lim = gnd i th pin voltage 0 current sense threshold (mv) 40 60 80 0.6 1.0 38582 g13 20 0 0.2 0.4 0.8 1.2 1.4 C20 C40 pulse-skipping forced continuous burst mode operation (falling) burst mode operation (rising) i lim = gnd i lim = float i lim = intv cc 5% duty cycle duty cycle (%) 0 maximum current sense voltage (mv) 40 60 80 38582 g15 20 0 20 40 50 100 80 60 10 30 90 70 i lim = intv cc i lim = float i lim = gnd temperature (c) C45 110 quiescent current (a) 190 C20 30 55 130 38582 g17 230 210 150 130 170 5 80 105 pllin/mode = 0 v in = 12v v out = 3.3v one channel on temperature (c) C45 shutdown current (a) 8 9 10 30 80 38582 g18 7 6 C20 5 55 105 130 5 4 input voltage (v) 0 5.0 intv cc voltage (v) 5.1 5.1 5.2 5.2 5101520 38582 g12 25 30 35 40
ltc3858-2 7 38582f typical performance characteristics soft-start pull-up current vs temperature shutdown (run) threshold vs temperature regulated feedback voltage vs temperature senseC pin input current vs temperature shutdown input current vs input voltage oscillator frequency vs temperature undervoltage lockout threshold vs temperature temperature (c) C45 ss pull-up current (a) 1.15 30 38582 g19 1.00 0.90 C20 5 55 0.85 0.80 1.20 1.10 1.05 0.95 80 105 130 temperature (c) C45 0.90 run pin voltage (v) 0.95 1.05 1.10 1.15 1.40 1.25 5 55 80 38582 g20 1.00 1.30 1.35 1.20 C20 30 105 130 temperature (c) C45 regulated feedback voltage (mv) 806 30 38582 g21 800 796 C20 5 55 794 792 808 804 802 798 80 105 130 temperature (c) C45 C600 sense C current (a) C550 C200 C150 50 C50 C20 30 55 130 38582 g22 0 C100 C400 C350 C500 C450 C250 C300 5 80 105 v out = 3.3v v out = 28v input voltage (v) 5 8 10 14 20 30 38582 g23 6 4 10 15 25 35 40 2 0 12 input current (a) oscillator frequency vs input voltage temperature (c) C45 frequency (khz) 700 30 38582 g24 400 200 C20 5 55 100 0 800 600 500 300 80 105 130 freq = intv cc freq = gnd intv cc vs load current input voltage (v) 5 oscillator frequency (khz) 352 354 356 20 30 38582 g25 350 348 10 15 25 35 40 346 344 freq = gnd temperature (c) C45 3.4 intv cc voltage (v) 3.5 3.7 3.8 3.9 4.4 4.1 5 55 80 38582 g26 3.6 4.2 4.3 4.0 C20 30 105 130 load current (ma) 0 intv cc voltage (v) 5.25 40 38582 g27 4.50 20 60 4.00 5.50 5.00 4.75 4.25 80 100 extv cc = 5v extv cc = 8.5v extv cc = 0v v in = 12v
ltc3858-2 8 38582f pin functions sense1 C , sense2 C (pin 1, pin 9): the (C) input to the differential current comparators. when greater than intv cc C 0.5v, the sense C pin supplies current to the current comparator. freq (pin 2): the frequency control pin for the internal voltage-controlled oscillator (vco). connecting this pin to gnd forces the vco to a fixed low frequency of 350khz. connecting this pin to intv cc forces the vco to a fixed high frequency of 535khz. other frequencies between 50khz and 900khz can be programmed using a resistor between freq and gnd. an internal 20a pull-up current develops the voltage to be used by the vco to control the frequency phasmd (pin 3): control input to phase selector which determines the phase relationships between controller 1, controller 2 and the clkout signal. pulling this pin to ground forces tg2 and clkout to be out of phase 180 and 60 with respect to tg1. connecting this pin to in- tv cc forces tg2 and clkout to be out of phase 240 and 120 with respect to tg1. floating this pin forces tg2 and clkout to be out of phase 180 and 90 with respect to tg1. refer to the table 1. clkout (pin 4): output clock signal available to daisy- chain other controller ics for additional mosfet driver stages/phases. the output levels swing from intv cc to ground. pllin/mode (pin 5): external synchronization input to phase detector and forced continuous mode input. when an external clock is applied to this pin, the phase-locked loop will force the rising tg1 signal to be synchronized with the rising edge of the external clock. when not syn- chronizing to an external clock, this input, which acts on both controllers, determines how the ltc3858-2 operates at light loads. pulling this pin to ground selects burst mode operation. an internal 100k resistor to ground also invokes burst mode operation when the pin is floated. tying this pin to intv cc forces continuous inductor current operation. tying this pin to a voltage greater than 1.2v and less than intv cc C 1.3v selects pulse-skipping operation. sgnd (pin 6, exposed pad pin 33): small-signal ground common to both controllers, must be routed separately from high current grounds to the common (C) terminals of the c in capacitors. the exposed pad must be soldered to the pcb for rated thermal performance. run1, run2 (pin 7, pin 8): digital run control inputs for each controller. forcing either of these pins below 1.2v shuts down that controller. forcing both of these pins below 0.7v shuts down the entire ltc3858-2, reducing quiescent current to approximately 8a. i lim (pin 28): current comparator sense voltage range inputs. tying this pin to sgnd, float or intv cc sets the maximum current sense threshold to one of three different levels for both comparators.
ltc3858-2 9 38582f pin functions intv cc (pin 19): output of the internal linear low dropout regulator. the driver and control circuits are powered from this voltage source. must be decoupled to power ground with a minimum of 4.7f ceramic or other low esr ca- pacitor. do not use the intv cc pin for any other purpose. extv cc (pin 20): external power input to an internal ldo connected to intv cc . this ldo supplies intv cc power, bypassing the internal ldo powered from v in whenever extv cc is higher than 4.7v. see extv cc connection in the applications information section. do not exceed 14v on this pin. pgnd (pin 21): driver power ground. connects to the sources of bottom (synchronous) n-channel mosfets and the (C) terminal(s) of c in . v in (pin 22): main input supply pin. a bypass capacitor should be tied between this pin and the signal ground pin. bg1, bg2 (pin 23, pin 18): high current gate drives for bottom (synchronous) n-channel mosfets. voltage swing at these pins is from ground to intv cc . boost1, boost2 (pin 24, pin 17): bootstrapped supplies to the topside floating drivers. capacitors are connected between the boost and sw pins and schottky diodes are tied between the boost and intv cc pins. voltage swing at the boost pins is from intv cc to (v in + intv cc ). sw1, sw2 (pin 25, pin 16): switch node connections to inductors. tg1, tg2 (pin 26, pin 15): high current gate drives for top n-channel mosfets. these are the outputs of float- ing drivers with a voltage swing equal to intv cc C 0.5v superimposed on the switch node voltage sw. pgood1, pgood2 (pin 27, pin 14): open-drain logic output. pgood1,2 is pulled to ground when the voltage on the v fb1,2 pin is not within 10% of its set point. ss1, ss2 (pin 29, pin 13): external soft-start input. the ltc3858-2 regulates the v fb1,2 voltage to the smaller of 0.8v or the voltage on the ss1,2 pin. an internal 1a pull- up current source is connected to this pin. a capacitor to ground at this pin sets the ramp time to final regulated output voltage. alternatively, a resistor divider on another voltage supply connected to this pin allows the ltc3858-2 output to track the other supply during start-up. i th1 , i th2 (pin 30, pin 12): error amplifier outputs and switching regulator compensation points. each associ- ated channels current comparator trip point increases with this control voltage. v fb1 , v fb2 (pin 31, pin 11): receives the remotely sensed feedback voltage for each controller from an external resistive divider across the output. sense1 + , sense2 + (pin 32, pin 10): the (+) input to the differential current comparators that are normally connected to inductor dcr sensing networks or current sensing resistors. the i th pin voltage and controlled offsets between the sense C and sense + pins in conjunction with r sense set the current trip threshold.
ltc3858-2 10 38582f functional diagram sw 25, 16 top boost 24, 17 tg 26, 15 c b c in d d b clkout pgnd bot bg 23, 18 intv cc intv cc v in c out v out 38582 fd r sense drop out det bot top on s r q q shdn sleep 0.425v icmp 2.7v 0.55v ir 3mv slope comp duplicate for second controller channel sense + 32, 10 sense C 1, 9 pgood1 v fb1 0.88v 0.72v l 27 21 + C + C + C + C pgood2 freq v fb2 0.88v 0.72v + C + C + C + C 14 + C + C switch logic v fb 31, 11 r a c c r c c c2 r b 0.80v track/ss 0.88v 0.5a 11v run 7, 8 i th 30, 12 ss 29, 13 + C c ss 1a shdn current limit foldback shdn rst 2(v fb ) 4 phasmd 3 2 pllin/mode 20a vco ldo en intv cc 5.1v sync det 100k c lp clk2 clk1 5 i lim 28 v in extv cc 20 22 ldo pfd en 4.7v 5.1v + C 19 sgnd 6 ea ov
ltc3858-2 11 38582f table 1. summary of the differences between ltc3858, ltc3858-1 and ltc3858-2 ltc3858 ltc3858-1 ltc3858-2 short-circuit latchoff feature? yes, but can be defeated yes, but can be defeated not present overvoltage protection bg forced on (bottom mosfet crowbar) bg forced on (bottom mosfet crowbar) bg not forced on (behavior depends on light load mode) optional tracking start-up? no no yes independent pgood1 and pgood2 pins? yes no, pgood1 only yes clkout/phasmd pins for polyphase yes no yes adjustable current limit (i lim pin) yes no yes package 5mm 5mm qfn 4mm 5mm qfn and narrow ssop 5mm 5mm qfn operation (refer to the functional diagram) table 1 summarizes the differences between the ltc3858-2 and its sister parts, the ltc3858 and ltc3858-1. the ltc3858-2 uses a constant frequency, current mode step-down architecture with the two controller channels operating 180 degrees out of phase. during normal op- eration, each external top mosfet is turned on when the clock for that channel sets the rs latch, and is turned off when the main current comparator, icmp , resets the rs latch. the peak inductor current at which icmp trips and resets the latch is controlled by the voltage on the i th pin, which is the output of the error amplifier, ea. the error amplifier compares the output voltage feedback signal at the v fb pin (which is generated with an external resistor divider connected across the output voltage, v out , to ground) to the internal 0.800v reference voltage. when the load current increases, it causes a slight decrease in v fb relative to the reference, which causes the ea to increase the i th voltage until the average inductor current matches the new load current. after the top mosfet is turned off each cycle, the bottom mosfet is turned on until either the inductor current starts to reverse, as indicated by the current comparator ir, or the beginning of the next clock cycle. intv cc /extv cc power power for the top and bottom mosfet drivers and most other internal circuitry is derived from the intv cc pin. when the extv cc pin is left open or tied to a voltage less than 4.7v, the v in ldo (low dropout linear regulator) supplies 5.1v from v in to intv cc . if extv cc is taken above 4.7v, the v in ldo is turned off and the extv cc ldo is turned on. once enabled, the extv cc ldo supplies 5.1v from extv cc to intv cc . using the extv cc pin allows the intv cc power to be derived from a high efficiency external source such as one of the ltc3858-2 switching regulator outputs. each top mosfet driver is biased from the floating boot- strap capacitor, c b , which normally recharges during each switching cycle through an external diode when the top mosfet turns off. if the input voltage, v in , decreases to a voltage close to v out , the loop may enter dropout and attempt to turn on the top mosfet continuously. the dropout detector detects this and forces the top mosfet off for about one-twelfth of the clock period every tenth cycle to allow c b to recharge.
ltc3858-2 12 38582f operation (refer to the functional diagram) shutdown and start-up (run1, run2 and ss1, ss2 pins) the two channels of the ltc3858-2 can be independently shut down using the run1 and run2 pins. pulling either of these pins below 1.26v shuts down the main control loop for that controller. pulling both pins below 0.7v disables both controllers and most internal circuits, including the intv cc ldos. in this state, the ltc3858-2 draws only 8a of quiescent current. the run pin may be externally pulled up or driven directly by logic. when driving the run pin with a low impedance source, do not exceed the absolute maximum rating of 8v. the run pin has an internal 11v voltage clamp that allows the run pin to be connected through a resistor to a higher voltage (for example, v in ), so long as the maximum current into the run pin does not exceed 100a. the start-up of each controllers output voltage, v out , is controlled by the voltage on the ss pin for that channel. when the voltage on the ss pin is less than the 0.8v internal reference, the ltc3858-2 regulates the v fb volt- age to the ss pin voltage instead of the 0.8v reference. this allows the ss pin to be used to program a soft-start by connecting an external capacitor from the ss pin to sgnd. an internal 1a pull-up current charges this ca- pacitor creating a voltage ramp on the ss pin. as the ss voltage rises linearly from 0v to 0.8v (and beyond up to the absolute maximum rating of 6v), the output voltage v out rises smoothly from zero to its final value. alternatively, the ss pin can be used to cause the start- up of v out to track that of another supply. typically, this requires connecting to the ss pin an external resistor divider from the other supply to ground (see the applica- tions information section). light load current operation (burst mode operation, pulse-skipping or forced continuous) (pllin/mode pin) the ltc3858-2 can be enabled to enter high efficiency burst mode operation, constant frequency pulse-skipping mode, or forced continuous conduction mode at low load currents. to select burst mode operation, tie the pllin/ mode pin to ground. to select forced continuous operation, tie the pllin/mode pin to intv cc . to select pulse-skipping mode, tie the pllin/mode pin to a dc voltage greater than 1.2v and less than intv cc C 1.3v. when a controller is enabled for burst mode operation, the minimum peak current in the inductor is set to approxi- mately 30% of the maximum sense voltage even though the voltage on the i th pin indicates a lower value. if the average inductor current is higher than the load current, the error amplifier ea will decrease the voltage on the i th pin. when the i th voltage drops below 0.425v, the internal sleep signal goes high (enabling sleep mode) and both external mosfets are turned off. in sleep mode, much of the internal circuitry is turned off, reducing the quiescent current. if one channel is shut down and the other channel is in sleep mode, the ltc3858-2 draws only 170a of quiescent current. if both channels are in sleep mode, the ltc3858-2 draws only 300a of qui- escent current. in sleep mode, the load current is supplied by the output capacitor. as the output voltage decreases, the eas output begins to rise. when the output voltage drops enough, the i th pin is reconnected to the output of the ea, the sleep signal goes low, and the controller resumes normal operation by turning on the top external mosfet on the next cycle of the internal oscillator. when a controller is enabled for burst mode operation, the inductor current is not allowed to reverse. the reverse current comparator, ir, turns off the bottom external mosfet just before the inductor current reaches zero, preventing it from reversing and going negative. thus, the controller is in discontinuous operation.
ltc3858-2 13 38582f operation (refer to the functional diagram) the switching frequency of the ltc3858-2s controllers can be selected using the freq pin. if the pllin/mode pin is not being driven by an external clock source, the freq pin can be tied to sgnd, tied to intv cc or programmed through an external resistor. tying freq to sgnd selects 350khz while tying freq to intv cc selects 535khz. placing a resistor between freq and sgnd allows the frequency to be programmed between 50khz and 900khz, as shown in figure 10. a phase-locked loop (pll) is available on the ltc3858-2 to synchronize the internal oscillator to an external clock source that is connected to the pllin/mode pin. the phase detector adjusts the voltage (through an internal lowpass filter) of the vco input to align the turn-on of controller 1s external top mosfet to the rising edge of the synchronizing signal. thus, the turn-on of controller 2s external top mosfet is 180 degrees out of phase to the rising edge of the external clock source. the vco input voltage is pre-biased to the operating frequency set by the freq pin before the external clock is applied. if prebiased near the external clock frequency, the pll loop only needs to make slight changes to the vco input in order to synchronize the rising edge of the external clocks to the rising edge of tg1. the ability to pre-bias the loop filter allows the pll to lock-in rapidly without deviating far from the desired frequency. the typical capture range of the phase-locked loop is from approximately 55khz to 1mhz, with a guarantee over all manufacturing variations to be between 75khz and 850khz. in other words, the ltc3858-2s pll is guaranteed to lock to an external clock source whose frequency is between 75khz and 850khz. the typical input clock thresholds on the pllin/mode pin are 1.6v (rising) and 1.1v (falling). in forced continuous operation or when clocked by an external clock source to use the phase-locked loop (see the frequency selection and phase-locked loop section), the inductor current is allowed to reverse at light loads or under large transient conditions. the peak inductor current is determined by the voltage on the i th pin, just as in normal operation. in this mode, the efficiency at light loads is lower than in burst mode operation. however, continuous operation has the advantages of lower output voltage ripple and less interference to audio circuitry. in forced continuous mode, the output ripple is independent of load current. when the pllin/mode pin is connected for pulse-skipping mode, the ltc3858-2 operates in pwm pulse-skipping mode at light loads. in this mode, constant frequency operation is maintained down to approximately 1% of designed maximum output current. at very light loads, the current comparator, icmp , may remain tripped for several cycles and force the external top mosfet to stay off for the same number of cycles (i.e., skipping pulses). the inductor current is not allowed to reverse (discontinuous operation). this mode, like forced continuous operation, exhibits low output ripple as well as low audio noise and reduced rf interference when compared to burst mode operation. it provides higher light load efficiency than forced continuous mode, but not nearly as high as burst mode operation. frequency selection and phase-locked loop (freq and pllin/mode pins) the selection of switching frequency is a trade-off between efficiency and component size. low frequency opera- tion increases efficiency by reducing mosfet switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage.
ltc3858-2 14 38582f operation (refer to the functional diagram) polyphase ? applications (clkout and phasmd pins) the ltc3858-2 features two pins (clkout and phasmd) that allow other controller ics to be daisy-chained with the ltc3858-2 in polyphase applications. the clock output signal on the clkout pin can be used to synchronize additional power stages in a multiphase power supply solution feeding a single, high current output or multiple separate outputs. the phasmd pin is used to adjust the phase of the clkout signal as well as the relative phases between the two internal controllers, as summarized in table 2. the phases are calculated relative to the zero degrees phase being defined as the rising edge of the top gate driver output of controller 1 (tg1). the clkout pin swings from ground to intv cc with a pull-down impedance of 120 and a pull-up impedance of 150. table 2 v phasmd controller 2-phase clkout phase gnd 180 60 floating 180 90 intv cc 240 120 output overvoltage protection an overvoltage (ov) comparator guards against transient overshoots as well as other more serious conditions that may overvoltage the output. when the v fb pin rises by more than 10% above its regulation point of 0.800v, the top mosfet is turned off until the overvoltage condition is cleared. the state of the bottom mosfet during the overvoltage condition depends on the light load mode of operation, as selected by the pllin/mode pin. in forced continu- ous mode, the bottom gate driver bg naturally turns on whenever the top gate driver tg is off, resulting in nega- tive inductor current which discharges the output to (try to) bring it back into regulation. in pulse-skipping mode, bg is held off most of the time but is turned on for a brief pulse every ten clock cycles (for an effective bg-on duty cycle of ~1%) to refresh the boost-sw capacitor. this causes a slightly negative average inductor current which, in addition to whatever load current is present, may slowly discharge the output. in burst mode operation, bg is held off continuously, leaving only the load current to discharge the output to bring it back into regulation. power good (pgood1 and pgood2) pins each pgood pin is connected to an open drain of an internal n-channel mosfet. the mosfet turns on and pulls the pgood pin low when the corresponding v fb pin voltage is not within 10% of the 0.8v reference voltage. the pgood pin is also pulled low when the corresponding run pin is low (shut down). when the v fb pin voltage is within the 10% requirement, the mosfet is turned off and the pin is allowed to be pulled up by an external resistor to a source no greater than 6v. foldback current when the output voltage falls to less than 70% of its nominal level, foldback current limiting is activated, pro- gressively lowering the peak current limit in proportion to the severity of the overcurrent or short-circuit condition. foldback current limiting is disabled during the soft-start interval (as long as the v fb voltage is keeping up with the track/ss voltage). theory and benefits of 2-phase operation why the need for 2-phase operation? up until the 2-phase family, constant frequency dual switching regulators operated both channels in phase (i.e., single phase operation). this means that both switches turned on at the same time, causing current pulses of up to twice the amplitude of those for one regulator to be drawn from the input capacitor and battery. these large amplitude current pulses increased the total rms current flowing from the input capacitor, requiring the use of more expensive input capacitors and increasing both emi and losses in the input capacitor and battery. with 2-phase operation, the two channels of the dual switching regulator are operated 180 degrees out of phase. this effectively interleaves the current pulses drawn by the switches, greatly reducing the overlap time where they add together. the result is a significant reduction in total rms input current, which in turn allows less expensive input capacitors to be used, reduces shielding requirements for emi and improves real world operating efficiency.
ltc3858-2 15 38582f operation (refer to the functional diagram) figure 1. input waveforms comparing single-phase (a) and 2-phase (b) operation for dual switching regulators converting 12v to 5v and 3.3v at 3a each. the reduced input ripple with the 2-phase regulator allows less expensive input capacitors, reduces shielding requirements for emi and improves efficiency figure 1 compares the input waveforms for a representative single-phase dual switching regulator to the ltc3858-2 2-phase dual switching regulator. an actual measurement of the rms input current under these conditions shows that 2-phase operation dropped the input current from 2.53a rms to 1.55a rms . while this is an impressive reduction in itself, remember that the power losses are proportional to i rms 2 , meaning that the actual power wasted is reduced by a factor of 2.66. the reduced input ripple voltage also means less power is lost in the input power path, which could include batteries, switches, trace/connector resistances and protection circuitry. improvements in both conducted and radiated emi also directly accrue as a result of the reduced rms input current and voltage. of course, the improvement afforded by 2-phase opera- tion is a function of the dual switching regulators relative duty cycles which, in turn, are dependent upon the input voltage v in (duty cycle = v out /v in ). figure 2 shows how the rms input current varies for single phase and 2-phase operation for 3.3v and 5v regulators over a wide input voltage range. it can readily be seen that the advantages of 2-phase op- eration are not just limited to a narrow operating range, for most applications is that 2-phase operation will reduce the input capacitor requirement to that for just one chan- nel operating at maximum current and 50% duty cycle. i in(meas) = 2.53a rms i in(meas) = 1.55a rms 38582 f01 5v switch 20v/div 3.3v switch 20v/div input current 5a/div input voltage 500mv/div figure 2. rms input current comparison input voltage (v) 0 input rms current (a) 3.0 2.5 2.0 1.5 1.0 0.5 0 10 20 30 40 38582 f02 single phase dual controller 2-phase dual controller v o1 = 5v/3a v o2 = 3.3v/3a
ltc3858-2 16 38582f applications information figure 3. sense lines placement with inductor or sense resistor the typical application on the first page is a basic ltc3858-2 application circuit. ltc3858-2 can be config- ured to use either dcr (inductor resistance) sensing or low value resistor sensing. the choice between the two current sensing schemes is largely a design trade-off between cost, power consumption and accuracy. dcr sensing is becoming popular because it saves expensive current sensing resistors and is more power efficient, especially in high current applications. however, current sensing resistors provide the most accurate current limits for the controller. other external component selection is driven by the load requirement, and begins with the selection of r sense (if r sense is used) and inductor value. next, the power mosfets and schottky diodes are selected. finally, input and output capacitors are selected. current limit programming the i lim pin is a tri-level logic input which sets the maximum current limit of the converter. when i lim is grounded, the maximum current limit threshold voltage of the current comparator is programmed to be 30mv. when i lim is floated, the maximum current limit threshold is 50mv. when i lim is tied to intv cc , the maximum current limit threshold is set to 75mv. sense + and sense C pins the sense + and sense C pins are the inputs to the current comparators. the common mode voltage range on these pins is 0v to 28v (abs max), enabling the ltc3858-2 to regulate output voltages up to a nominal 24v (allowing plenty of margin for tolerances and transients). the sense + pin is high impedance over the full common mode range, drawing at most 1a. this high impedance allows the current comparators to be used in inductor dcr sensing. the impedance of the sense C pin changes depending on the common mode voltage. when sense C is less than intv cc C 0.5v, a small current of less than 1a flows out of the pin. when sense C is above intv cc + 0.5v, a higher current (~550a) flows into the pin. between intv cc C 0.5v and intv cc + 0.5v, the current transitions from the smaller current to the higher current. filter components mutual to the sense lines should be placed close to the ltc3858-2, and the sense lines should run close together to a kelvin connection underneath the current sense element (shown in figure 3). sensing cur- rent elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. if inductor dcr sensing is used (figure 4b), resistor r1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. c out to sense filter, next to the controller inductor or r sense 3858 f03 low value resistor current sensing a typical sensing circuit using a discrete resistor is shown in figure 4a. r sense is chosen based on the required output current. the current comparator has a maximum threshold v sense(max) determined by the i lim setting. the current comparator threshold voltage sets the peak of the induc- tor current, yielding a maximum average output current, i max , equal to the peak value less half the peak-to-peak ripple current, i l . to calculate the sense resistor value, use the equation: r sense = v sense(max) i max + i l 2 when using the controller in very low dropout conditions, the maximum output current level will be reduced due to the internal compensation required to meet stability cri- terion for buck regulators operating at greater than 50% duty factor. a curve is provided in the typical performance characteristics section to estimate this reduction in peak output current depending upon the operating duty factor.
ltc3858-2 17 38582f (4a) using a resistor to sense current (4b) using the inductor dcr to sense current figure 4. current sensing methods applications information inductor dcr sensing for applications requiring the highest possible efficiency at high load currents, the ltc3850 is capable of sensing the voltage drop across the inductor dcr, as shown in figure 4b. the dcr of the inductor represents the small amount of dc resistance of the copper wire, which can be less than 1m for todays low value, high current inductors. in a high current application requiring such an inductor, power loss through a sense resistor would cost several points of efficiency compared to inductor dcr sensing. if the external r1||r2 ? c1 time constant is chosen to be exactly equal to the l/dcr time constant, the voltage drop across the external capacitor is equal to the drop across the inductor dcr multiplied by r2/(r1 + r2). r2 scales the voltage across the sense terminals for applications where the dcr is greater than the target sense resistor value. to properly dimension the external filter components, the dcr of the inductor must be known. it can be measured using a good rlc meter, but the dcr tolerance is not always the same and varies with temperature; consult the manufacturers data sheets for detailed information. using the inductor ripple current value from the inductor value calculation section, the target sense resistor value is: r sense(equiv) = v sense(max) i max + i l 2 to ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the maximum current sense thresh- old voltage (v sense(max) ) in the electrical characteristics table (30mv, 50mv or 75mv depending on the state of the i lim pin). next, determine the dcr of the inductor. when provided, use the manufacturers maximum value, usually given at 20c. increase this value to account for the temperature coefficient of copper, which is approximately 0.4%/c. a conservative value for t l(max) is 100c. to scale the maximum inductor dcr to the desired sense resistor (r d ) value, use the divider ratio: r d = r sense(equiv) dcr max at t l(max) v in v in intv cc boost tg sw bg place capacitor near sense pins sense + sense C sgnd ltc3858-2 v out r sense 38582 f04a v in v in intv cc boost tg sw bg *place c1 near sense pins inductor dcr l sense + sense C sgnd ltc3858-2 v out 38582 f04b r1 r2 c1* (r1 || r2) t c1 = l dcr r sense(eq) = dcr r2 r1 + r2
ltc3858-2 18 38582f applications information c1 is usually selected to be in the range of 0.1f to 0.47f. this forces r1||r2 to around 2k, reducing error that might have been caused by the sense + pins 1a current. the equivalent resistance r1||r2 is scaled to the room temperature inductance and maximum dcr: r1|| r2 = l dcr at 20 c () ?c1 the sense resistor values are: r1 = r1|| r2 r d ; r2 = r1? r d 1C r d the maximum power loss in r1 is related to duty cycle, and will occur in continuous mode at the maximum input voltage: p loss r1 = v in(max) Cv out () ?v out r1 ensure that r1 has a power rating higher than this value. if high efficiency is necessary at light loads, consider this power loss when deciding whether to use inductor dcr sensing or sense resistors. light load power loss can be modestly higher with a dcr network than with a sense resistor, due to the extra switching losses incurred through r1. however, dcr sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. peak efficiency is about the same with either method. inductor value calculation the operating frequency and inductor selection are inter- related in that higher operating frequencies allow the use of smaller inductor and capacitor values. so why would anyone ever choose to operate at lower frequencies with larger components? the answer is efficiency. a higher frequency generally results in lower efficiency because of mosfet gate charge losses. in addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. the inductor value has a direct effect on ripple current. the inductor ripple current i l decreases with higher induc- tance or higher frequency and increases with higher v in : i l = 1 f () l () v out 1C v out v in ? ? ? ? ? ? accepting larger values of i l allows the use of low inductances, but results in higher output voltage ripple and greater core losses. a reasonable starting point for setting ripple current is i l = 0.3(i max ). the maximum i l occurs at the maximum input voltage. the inductor value also has secondary effects. the tran- sition to burst mode operation begins when the average inductor current required results in a peak current below 30% of the current limit determined by r sense . lower inductor values (higher i l ) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. in burst mode operation, lower inductance values will cause the burst frequency to decrease. inductor core selection once the value for l is known, the type of inductor must be selected. high efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance value selected. as inductance increases, core losses go down. unfortunately, increased inductance requires more turns of wire and therefore copper losses will increase. ferrite designs have very low core loss and are preferred for high switching frequencies, so design goals can con- centrate on copper loss and preventing saturation. ferrite core material saturates hard, which means that induc- tance collapses abruptly when the peak design current is exceeded. this results in an abrupt increase in inductor ripple current and consequent output voltage ripple. do not allow the core to saturate!
ltc3858-2 19 38582f applications information power mosfet and schottky diode (optional) selection two external power mosfets must be selected for each controller in the ltc3858-2: one n-channel mosfet for the top (main) switch, and one n-channel mosfet for the bottom (synchronous) switch. the peak-to-peak drive levels are set by the intv cc voltage. this voltage is typically 5.2v during start-up (see extv cc pin connection). consequently, logic-level threshold mosfets must be used in most applications. the only exception is if low input voltage is expected (v in < 4v); then, sub-logic level threshold mosfets (v gs(th) < 3v) should be used. pay close attention to the bv dss speci- fication for the mosfets as well; many of the logic-level mosfets are limited to 30v or less. selection criteria for the power mosfets include the on-resistance, r ds(on) , miller capacitance, c miller , input voltage and maximum output current. miller capacitance, c miller , can be approximated from the gate charge curve usually provided on the mosfet manufacturers data sheet. c miller is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in v ds . this result is then multiplied by the ratio of the application applied v ds to the gate charge curve specified v ds . when the ic is operating in continuous mode the duty cycles for the top and bottom mosfets are given by: main switch duty cycle = v out v in synchronous switch duty cycle = v in ? v out v in the mosfet power dissipations at maximum output current are given by: p main = v out v in i max () 2 1 + () r ds(on) + v in () 2 i max 2 ? ? ? ? ? ? r dr () c miller () ? 1 v intvcc Cv thmin + 1 v thmin ? ? ? ? ? ? f () p sync = v in Cv out v in i max () 2 1 + () r ds(on) where is the temperature dependency of r ds(on) and r dr (approximately 2) is the effective driver resistance at the mosfets miller threshold voltage. v thmin is the typical mosfet minimum threshold voltage. both mosfets have i 2 r losses while the topside n-channel equation includes an additional term for transition losses, which are highest at high input voltages. for v in < 20v the high current efficiency generally improves with larger mosfets, while for v in > 20v the transition losses rapidly increase to the point that the use of a higher r ds(on) device with lower c miller actually provides higher efficiency. the synchronous mosfet losses are greatest at high input voltage when the top switch duty factor is low or during a short-circuit when the synchronous switch is on close to 100% of the period. the term (1+ ) is generally given for a mosfet in the form of a normalized r ds(on) vs temperature curve, but = 0.005/c can be used as an approximation for low voltage mosfets. the optional schottky diodes d3 and d4 shown in figure 13 conduct during the dead-time between the conduction of the two power mosfets. this prevents the body diode of the bottom mosfet from turning on, storing charge during the dead-time and requiring a reverse recovery period that could cost as much as 3% in efficiency at high v in . a 1a to 3a schottky is generally a good compromise for both regions of operation due to the relatively small average current. larger diodes result in additional transition losses due to their larger junction capacitance.
ltc3858-2 20 38582f applications information c in and c out selection the selection of c in is simplified by the 2-phase architec- ture and its impact on the worst-case rms current drawn through the input network (battery/fuse/capacitor). it can be shown that the worst-case capacitor rms current occurs when only one controller is operating. the controller with the highest (v out )(i out ) product needs to be used in the formula shown in equation 1 to determine the maximum rms capacitor current requirement. increasing the out- put current drawn from the other controller will actually decrease the input rms ripple current from its maximum value. the out-of-phase technique typically reduces the input capacitors rms ripple current by a factor of 30% to 70% when compared to a single phase power supply solution. in continuous mode, the source current of the top mosfet is a square wave of duty cycle (v out )/(v in ). to prevent large voltage transients, a low esr capacitor sized for the maximum rms current of one channel must be used. the maximum rms capacitor current is given by: c in required i rms i max v in v out () v in Cv out () ? ? ? ? 1/ 2 (1) equation 1 has a maximum at v in = 2v out , where i rms = i out /2. this simple worst-case condition is commonly used for design because even significant deviations do not offer much relief. note that capacitor manufacturers ripple current ratings are often based on only 2000 hours of life. this makes it advisable to further derate the capacitor, or to choose a capacitor rated at a higher temperature than required. several capacitors may be paralleled to meet size or height requirements in the design. due to the high operating frequency of the ltc3858-2, ceramic capacitors can also be used for c in . always consult the manufacturer if there is any question. the benefit of 2-phase operation can be calculated by using equation 1 for the higher power controller and then calculating the loss that would have resulted if both controller channels switched on at the same time. the total rms power lost is lower when both controllers are operating due to the reduced overlap of current pulses required through the input capacitors esr. this is why the input capacitors requirement calculated above for the worst-case controller is adequate for the dual controller design. also, the input protection fuse resistance, battery resistance, and pc board trace resistance losses are also reduced due to the reduced peak currents in a 2-phase system. the overall benefit of a multiphase design will only be fully realized when the source impedance of the power supply/battery is included in the efficiency testing. the drains of the top mosfets should be placed within 1cm of each other and share a common c in (s). separat- ing the sources and c in may produce undesirable voltage and current resonances at v in . a small (0.1f to 1f) bypass capacitor between the chip v in pin and ground, placed close to the ltc3858-2, is also suggested. a small (1 to 10) resistor placed between c in (c1) and the v in pin provides further isolation between the two channels. the selection of c out is driven by the effective series resistance (esr). typically, once the esr requirement is satisfied, the capacitance is adequate for filtering. the output ripple ( v out ) is approximated by: v out ? i l esr + 1 8?f?c out ? ? ? ? ? ? where f o is the operating frequency, c out is the output capacitance and i l is the ripple current in the inductor. the output ripple is highest at maximum input voltage since i l increases with input voltage.
ltc3858-2 21 38582f applications information figure 6. using the ss pin to program soft-start setting output voltage the ltc3858-2 output voltages are each set by an exter- nal feedback resistor divider carefully placed across the output, as shown in figure 5. the regulated output voltage is determined by: v out = 0.8v 1 + r b r a ? ? ? ? ? ? to improve the frequency response, a feedforward ca- pacitor, c ff , may be used. great care should be taken to route the v fb line away from noise sources, such as the inductor or the sw line. soft-start (ss pins) the start-up of each v out is controlled by the voltage on the respective ss pin. when the voltage on the ss pin is less than the internal 0.8v reference, the ltc3858-2 regulates the v fb pin voltage to the voltage on the ss pin instead of 0.8v. the ss pin can be used to program an external soft-start function or to allow v out to track another supply during start-up. soft-start is enabled by simply connecting a capacitor from the ss pin to ground, as shown in figure 6. an internal 1a current source charges the capacitor, providing a linear ramping voltage at the ss pin. the ltc3858-2 will regulate the v fb pin (and hence v out ) according to the voltage on the ss pin, allowing v out to rise smoothly from 0v to its final regulated value. the total soft-start time will be approximately: t ss = c ss ? 0.8v 1 a 1/2 ltc3858-2 ss c ss sgnd 38582 f06 figure 5. setting output voltage 1/2 ltc3858-2 v fb v out r b c ff r a 38582 f05
ltc3858-2 22 38582f time output voltage 38582 f07a v x(master) v out(slave) time 38582 f07b output voltage v x(master) v out(slave) (7a) coincident tracking (7b) ratiometric tracking figure 7. two different modes of output voltage tracking alternatively, the ss pin can be used to track two (or more) supplies during start-up, as shown qualitatively in figures 7a and 7b. to do this, a resistor divider should be connected from the master supply (v x ) to the ss pin of the slave supply (v out ), as shown in figure 8. dur- ing start-up, v out will track v x according to the ratio set by the resistor divider: v x v out = r a r tracka ? r tracka + r trackb r a + r b applications information for coincident tracking (v out = v x during start-up): r a = r tracka r b = r trackb 1/2 ltc3858-2 v out v x v fb ss 38582 f08 r b r a r tracka r trackb figure 8. using the ss pin for tracking
ltc3858-2 23 38582f applications information intv cc regulators the ltc3858-2 features two separate internal p-channel low dropout linear regulators (ldo) that supply power at the intv cc pin from either the v in supply pin or the ext- v cc pin depending on the connection of the extv cc pin. intv cc powers the gate drivers and much of the internal circuitry. the v in ldo and the extv cc ldo regulate in- tv cc to 5.1v. each of these can supply a peak current of 50ma and must be bypassed to ground with a minimum of 4.7f low esr capacitor. regardless of what type of bulk capacitor is used, an additional 1f ceramic capacitor placed directly adjacent to the intv cc and pgnd pins is highly recommended. good bypassing is needed to supply the high transient currents required by the mosfet gate drivers and to prevent interaction between the channels. high input voltage applications in which large mosfets are being driven at high frequencies may cause the maxi- mum junction temperature rating for the ltc3858-2 to be exceeded. the intv cc current, which is dominated by the gate charge current, may be supplied by either the v in ldo or the extv cc ldo. when the voltage on the extv cc pin is less than 4.7v, the v in ldo is enabled. power dissipa- tion for the ic in this case is highest and is equal to v in ? i intvcc . the gate charge current is dependent on operating frequency as discussed in the efficiency considerations section. the junction temperature can be estimated by using the equations given in note 3 of the electrical char- acteristics. for example, the ltc3858-2 intv cc current is limited to less than 32ma from a 40v supply when not using the extv cc supply at 70c ambient temperature: t j = 70c + (32ma)(40v)(43c/w) = 125c to prevent the maximum junction temperature from be- ing exceeded, the input supply current must be checked while operating in forced continuous mode (pllin/mode = intv cc ) at maximum v in . when the voltage applied to extv cc rises above 4.7v, the v in ldo is turned off and the extv cc ldo is enabled. the extv cc ldo remains on as long as the voltage applied to extv cc remains above 4.5v. the extv cc ldo attempts to regulate the intv cc voltage to 5.1v, so while extv cc is less than 5.1v, the ldo is in dropout and the intv cc voltage is approximately equal to extv cc . when extv cc is greater than 5.1v, up to an absolute maximum of 14v, intv cc is regulated to 5.1v. using the extv cc ldo allows the mosfet driver and control power to be derived from one of the switching regulator outputs (4.7v v out 14v) during normal operation and from the v in ldo when the output is out of regulation (e.g., start-up, short-circuit). if more current is required through the extv cc ldo than is specified, an external schottky diode can be added between the extv cc and intv cc pins. in this case, do not apply more than 6v to the extv cc pin and make sure that extv cc v in . significant efficiency and thermal gains can be realized by powering intv cc from the output, since the v in cur- rent resulting from the driver and control currents will be scaled by a factor of (duty cycle)/(switcher efficiency). for 5v to 14v regulator outputs, this means connecting the extv cc pin directly to v out . tying the extv cc pin to an 8.5v supply reduces the junction temperature in the previous example from 125c to: t j = 70c + (32ma)(8.5v)(43c/w) = 82c however, for 3.3v and other low voltage outputs, additional circuitry is required to derive intv cc power from the output. the following list summarizes the four possible connec- tions for extv cc : 1. extv cc grounded. this will cause intv cc to be powered from the internal 5.1v regulator resulting in an efficiency penalty of up to 10% at high input voltages. 2. extv cc connected directly to v out . this is the normal connection for a 5v to 14v regulator and provides the highest efficiency. 3. extv cc connected to an external supply. if an external supply is available in the 5v to 14v range, it may be used to power extv cc . ensure that extv cc < v in . 4. extv cc connected to an output-derived boost network. for 3.3v and other low voltage regulators, efficiency gains can still be realized by connecting extv cc to an output-derived voltage that has been boosted to greater than 4.7v. this can be done with the capacitive charge pump shown in figure 9. ensure that extv cc < v in .
ltc3858-2 24 38582f applications information figure 9. capacitive charge pump for extv cc topside mosfet driver supply (c b , d b ) external bootstrap capacitors, c b , connected to the boost pins supply the gate drive voltages for the topside mosfets. capacitor c b in the functional diagram is charged though external diode d b from intv cc when the sw pin is low. when one of the topside mosfets is turned on, the driver places the c b voltage across the gate-source of the desired mosfet. this enhances the top mosfet switch and turns it on. the switch node voltage, sw, rises to v in and the boost pin follows. with the topside mosfet on, the boost voltage is above the input supply: v boost = v in + v intvcc . the value of the boost capacitor, c b , needs to be 100 times that of the total input capacitance of the top- side mosfet(s). the reverse breakdown of the external schottky diode must be greater than v in(max) . when adjusting the gate drive level, the final arbiter is the total input current for the regulator. if a change is made and the input current decreases, then the efficiency has improved. if there is no change in input current, then there is no change in efficiency. fault conditions: current limit and current foldback when the output current hits the current limit, the output voltage begins to drop. if the output voltage falls below 70% of its nominal output level, then the maximum sense voltage is progressively lowered to about half of its maximum selected value. under short-circuit condi- tions with very low duty cycles, the ltc3858-2 will begin cycle skipping in order to limit the short-circuit current. in this situation the bottom mosfet will be dissipating most of the power but less than in normal operation. the short-circuit ripple current is determined by the minimum on-time, t on(min) , of the ltc3858-2 (95ns), the input voltage and inductor value: i l(sc) = t on(min) v in l ? ? ? ? ? ? the resulting average short-circuit current is: i sc = 50% ? i lim(max) r sense C 1 2 i l(sc) phase-locked loop and frequency synchronization the ltc3858-2 has an internal phase-locked loop (pll) comprised of a phase frequency detector, a lowpass filter, and a voltage-controlled oscillator (vco). this allows the turn-on of the top mosfet of controller 1 to be locked to the rising edge of an external clock signal applied to the pllin/mode pin. the turn-on of controller 2s top mosfet is thus 180 degrees out of phase with the external clock. the phase detector is an edge sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. this type of phase detector does not exhibit false lock to harmonics of the external clock. when not prebiased, applying an external clock will invoke traditional pll operation. if the external clock frequency is greater than the internal oscillators frequency, f osc , then current is sourced continuously from the phase detector output, pulling up the vco input. when the external clock frequency is less than f osc , current is sunk continuously, pulling down the vco input. if the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time cor- responding to the phase difference. the voltage at the vco input is adjusted until the phase and frequency of the internal and external oscillators are identical. at the stable operating point, the phase detector output is high impedance and the internal filter capacitor, c lp , holds the voltage at the vco input. extv cc v in tg1 sw bg1 pgnd 1/2 ltc3858-2 r sense v out vn2222ll c out 38582 f09 mbot mtop c in v in l d bat85 bat85 bat85
ltc3858-2 25 38582f applications information note that the ltc3858-2 can only be synchronized to an external clock whose frequency is within range of the ltc3858-2s internal vco, which is nominally 55khz to 1mhz. this is guaranteed to be between 75khz and 850khz. typically, the external clock (on the pllin/mode pin) input high threshold is 1.6v, while the input low threshold is 1.1v. rapid phase-locking can be achieved by using the freq pin to set a free-running frequency near the desired synchronization frequency. the vcos input voltage is prebiased at a frequency corresponding to the frequency set by the freq pin. once prebiased, the pll only needs to adjust the frequency slightly to achieve phase-locking and synchronization. although it is not required that the free-running frequency be near external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the pll locks. table 3 summarizes the different states in which the freq pin can be used. table 3 freq pin pllin/mode pin frequency 0v dc voltage 350khz intv cc dc voltage 535khz resistor dc voltage 50khz to 900khz any of the above external clock phase-locked to external clock minimum on-time considerations minimum on-time, t on(min) , is the smallest time dura- tion that the ltc3858-2 is capable of turning on the top mosfet. it is determined by internal timing delays and the gate charge required to turn on the top mosfet. low duty cycle applications may approach this minimum on-time limit and care should be taken to ensure that: t on(min) < v out v in f () if the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles. the output voltage will continue to be regulated, but the ripple voltage and current will increase. the minimum on-time for the ltc3858-2 is approximately 95ns. however, as the peak sense voltage decreases the minimum on-time gradually increases up to about 130ns. this is of particular concern in forced continuous applica- tions with low ripple current at light loads. if the duty cycle drops below the minimum on-time limit in this situation, a significant amount of cycle skipping can occur with cor- respondingly larger current and voltage ripple. figure 10. relationship between oscillator frequency and resistor value at the freq pin freq pin resistor (k) 15 frequency (khz) 600 800 1000 35 45 55 25 38582 f10 400 200 500 700 900 300 100 0 65 75 85 95 105 115 125
ltc3858-2 26 38582f efficiency considerations the percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. it is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the most improvement. percent efficiency can be expressed as: %efficiency = 100% C (l1 + l2 + l3 + ...) where l1, l2, etc. are the individual losses as a percent- age of input power. although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in ltc3858-2 circuits: 1) ic v in current, 2) in- tv cc regulator current, 3) i 2 r losses, 4) topside mosfet transition losses. 1. the v in current is the dc input supply current given in the electrical characteristics table, which excludes mosfet driver and control currents. v in current typi- cally results in a small (<0.1%) loss. 2. intv cc current is the sum of the mosfet driver and control currents. the mosfet driver current results from switching the gate capacitance of the power mosfets. each time a mosfet gate is switched from low to high to low again, a packet of charge, dq, moves from intv cc to ground. the resulting dq/dt is a current out of intv cc that is typically much larger than the control circuit current. in continuous mode, i gatechg = f(q t + q b ), where q t and q b are the gate charges of the topside and bottom side mosfets. supplying intv cc from an output-derived power source through extv cc will scale the v in current required for the driver and control circuits by a factor of (duty cycle)/ (efficiency). for example, in a 20v to 5v application, 10ma of intv cc current results in approximately 2.5ma of v in current. this reduces the midcurrent loss from 10% or more (if the driver was powered directly from v in ) to only a few percent. applications information 3. i 2 r losses are predicted from the dc resistances of the fuse (if used), mosfet, inductor, current sense resis- tor, and input and output capacitor esr. in continuous mode the average output current flows through l and r sense , but is chopped between the topside mosfet and the synchronous mosfet. if the two mosfets have approximately the same r ds(on) , then the resistance of one mosfet can simply be summed with the resis- tances of l, r sense and esr to obtain i 2 r losses. for example, if each r ds(on) = 30m, r l = 50m, r sense = 10m and r esr = 40m (sum of both input and output capacitance losses), then the total resistance is 130m. this results in losses ranging from 3% to 13% as the output current increases from 1a to 5a for a 5v output, or a 4% to 20% loss for a 3.3v output. efficiency varies as the inverse square of v out for the same external components and output power level. the combined effects of increasingly lower output voltages and higher currents required by high performance digital systems is not doubling but quadrupling the importance of loss terms in the switching regulator system! 4. transition losses apply only to the topside mosfet(s), and become significant only when operating at high input voltages (t y pically 15v or greater). transition losses can be estimated from: transition loss = (1.7) ? v in ? 2 ? i o(max) ? c rss ? f other hidden losses such as copper trace and internal battery resistances can account for an additional 5% to 10% efficiency degradation in portable systems. it is very important to include these system level losses during the design phase. the internal battery and fuse resistance losses can be minimized by making sure that c in has adequate charge storage and very low esr at the switching frequency. a 25w supply will typically require a minimum of 20f to 40f of capacitance having a maximum of 20m to 50m of esr. the ltc3858-2 2-phase architecture typically halves this input capacitance requirement over competing solu- tions. other losses including schottky conduction losses during dead-time and inductor core losses generally account for less than 2% total additional loss.
ltc3858-2 27 38582f applications information checking transient response the regulator loop response can be checked by looking at the load current transient response. switching regulators take several cycles to respond to a step in dc (resistive) load current. when a load step occurs, v out shifts by an amount equal to i load (esr), where esr is the effective series resistance of c out . i load also begins to charge or discharge c out generating the feedback error signal that forces the regulator to adapt to the current change and return v out to its steady-state value. during this recovery time v out can be monitored for excessive overshoot or ringing, which would indicate a stability problem. opti- loop compensation allows the transient response to be optimized over a wide range of output capacitance and esr values. the availability of the i th pin not only allows optimization of control loop behavior, but it also provides a dc coupled and ac filtered closed-loop response test point. the dc step, rise time and settling at this test point truly reflects the closed-loop response. assuming a predominantly second order system, phase margin and/ or damping factor can be estimated using the percentage of overshoot seen at this pin. the bandwidth can also be estimated by examining the rise time at the pin. the i th external components shown in figure 13 circuit will provide an adequate starting point for most applications. the i th series r c -c c filter sets the dominant pole-zero loop compensation. the values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final pc layout is done and the particular output capacitor type and value have been determined. the output capacitors need to be selected because the various types and values determine the loop gain and phase. an output current pulse of 20% to 80% of full-load current having a rise time of 1s to 10s will produce output voltage and i th pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. placing a resistive load and a power mosfet directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce a realistic load step condition. the initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. this is why it is better to look at the i th pin signal which is in the feedback loop and is the filtered and compensated control loop response. the gain of the loop will be increased by increasing r c and the bandwidth of the loop will be increased by de- creasing c c . if r c is increased by the same factor that c c is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. the output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. a second, more severe transient is caused by switching in loads with large (>1f) supply bypass capacitors. the discharged bypass capacitors are effectively put in parallel with c out , causing a rapid drop in v out . no regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. if the ratio of c load to c out is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 ? c load . thus a 10f capacitor would require a 250s rise time, limiting the charging current to about 200ma.
ltc3858-2 28 38582f applications information design example as a design example for one channel, assume v in = 12v(nominal), v in = 22v (max), v out = 3.3v, i max = 5a, v sense(max) = 75mv and f = 350khz. the inductance value is chosen first based on a 30% ripple current assumption. the highest value of ripple current occurs at the maximum input voltage. tie the freq pin to gnd, generating 350khz operation. the minimum inductance for 30% ripple current is: i l = v out f () l () 1C v out v in ? ? ? ? ? ? a 4.7h inductor will produce 29% ripple current. the peak inductor current will be the maximum dc value plus one half the ripple current, or 5.73a. increasing the ripple current will also help ensure that the minimum on-time of 95ns is not violated. the minimum on-time occurs at maximum v in : t on(min) = v out v in f () = 3.3v 22v 350khz () = 429ns the equivalent r sense resistor value can be calculated by using the minimum value for the maximum current sense threshold (64mv): r sense 64mv 5.73a = 0.011 choosing 0.5% resistors: r a = 24.9k and r b = 77.7k yields an output voltage of 3.296v. the power dissipation on the topside mosfet can be easily estimated. choosing a fairchild fds6982s dual mosfet results in: r ds(on) = 0.035/0.022, c miller = 215pf. at maximum input voltage with t(estimated) = 50c: p main = 3.3v 22v 5a () 2 1 + 0.005 () 50 cC25 c () ? ? ? ? 0.035 () + 22v () 2 5a 2 2.5 () 215pf () ? 1 5v C 2.3v + 1 2.3v ? ? ? ? ? ? 350khz () = 331mw a short-circuit to ground will result in a folded back cur- rent of: i sc = 32mv 0.015 C 1 2 95ns 22v () 4.7h ? ? ? ? ? ? = 2.98a with a typical value of r ds(on) and = (0.005/c)(25c) = 0.125. the resulting power dissipated in the bottom mosfet is: p sync = 2.98a () 2 1.125 () 0.022 () = 220mw which is less than full-load conditions. c in is chosen for an rms current rating of at least 3a at temperature assuming only this channel is on. c out is chosen with an esr of 0.02 for low output ripple volt- age. the output ripple in continuous mode will be highest at the maximum input voltage. the output voltage ripple due to esr is approximately: v oripple = r esr ( i l ) = 0.02(1.45a) = 29mv p-p
ltc3858-2 29 38582f applications information pc board layout checklist when laying out the printed circuit board, the following checklist should be used to ensure proper operation of the ic. these items are also illustrated graphically in the layout diagram of figure 11. figure 12 illustrates the current waveforms present in the various branches of the 2-phase synchronous regulators operating in the continuous mode. check the following in your layout: 1. are the top n-channel mosfets mtop1 and mtop2 located within 1cm of each other with a common drain connection at c in ? do not attempt to split the input decoupling for the two channels as it can cause a large resonant loop. 2. are the signal and power grounds kept separate? the combined ic signal ground pin and the ground return of c intvcc must return to the combined c out (C) ter- minals. the path formed by the top n-channel mosfet, schottky diode and the c in capacitor should have short leads and pc trace lengths. the output capacitor (C) terminals should be connected as close as possible to the (C) terminals of the input capacitor by placing the capacitors next to each other and away from the schottky loop described above. 3. do the ltc3858-2 v fb pins resistive dividers connect to the (+) terminals of c out ? the resistive divider must be connected between the (+) terminal of c out and signal ground. the feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 4. are the sense C and sense + leads routed together with minimum pc trace spacing? the filter capacitor between sense + and sense C should be as close as possible to the ic. ensure accurate current sensing with kelvin connections at the sense resistor. 5. is the intv cc decoupling capacitor connected close to the ic, between the intv cc and the power ground pins? this capacitor carries the mosfet drivers cur- rent peaks. an additional 1f ceramic capacitor placed immediately next to the intv cc and pgnd pins can help improve noise performance substantially. 6. keep the switching nodes (sw1, sw2), top gate nodes (tg1, tg2), and boost nodes (boost1, boost2) away from sensitive small-signal nodes, especially from the opposites channels voltage and current sensing feed- back pins. all of these nodes have very large and fast moving signals and therefore should be kept on the output side of the ltc3858-2 and occupy minimum pc trace area. 7. use a modified star ground technique: a low imped- ance, large copper area central grounding point on the same side of the pc board as the input and output capacitors with tie-ins for the bottom of the intv cc decoupling capacitor, the bottom of the voltage feedback resistive divider and the sgnd pin of the ic.
ltc3858-2 30 38582f applications information pc board layout debugging start with one controller on at a time. it is helpful to use a dc-50mhz current probe to monitor the current in the inductor while testing the circuit. monitor the output switching node (sw pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage as well. check for proper performance over the operating voltage and current range expected in the ap- plication. the frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation thresholdtypically 10% of the maximum designed current level in burst mode operation. the duty cycle percentage should be maintained from cycle to cycle in a well-designed, low noise pcb implementation. variation in the duty cycle at a subharmonic rate can sug- gest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. overcompensation of the loop can be used to tame a poor pc layout if regulator bandwidth optimization is not required. only after each controller is checked for its individual performance should both controllers be turned on at the same time. a particularly difficult region of operation is when one controller channel is nearing its current comparator trip point when the other channel is turning on its top mosfet. this occurs around 50% duty cycle on either channel due to the phasing of the internal clocks and may cause minor duty cycle jitter. reduce v in from its nominal level to verify operation of the regulator in dropout. check the operation of the un- dervoltage lockout circuit by further lowering v in while monitoring the outputs to verify operation. investigate whether any problems exist only at higher out- put currents or only at higher input voltages. if problems coincide with high input voltages and low output currents, look for capacitive coupling between the boost, sw, tg, and possibly bg connections and the sensitive voltage and current pins. the capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the ic. this capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. if problems are encountered with high current output loading at lower input voltages, look for inductive coupling between c in , schottky and the top mosfet components to the sensitive current and voltage sensing traces. in addition, investigate common ground path voltage pickup between these components and the sgnd pin of the ic. an embarrassing problem, which can be missed in an otherwise properly working switching regulator, results when the current sensing leads are hooked up backwards. the output voltage under this improper hookup will still be maintained but the advantages of current mode control will not be realized. compensation of the voltage loop will be much more sensitive to component selection. this behavior can be investigated by temporarily shorting out the current sensing resistordont worry, the regulator will still maintain control of the output voltage.
ltc3858-2 31 38582f figure 11. recommended printed circuit layout diagram applications information c b2 c b1 r pu1 pgood1 v pull-up (<6v) c intvcc c in d1 1f ceramic m1 m2 m3 m4 d2 + c vin v out1 v in r in l1 l2 c out1 v out1 gnd v out2 38582 f11 + c out2 + r sense r sense r pu2 pgood2 v pull-up (<6v) f in 1f ceramic i th1 v fb1 sense1 + sense1 C freq sense2 C sense2 + v fb2 i th2 ss2 ss1 pgood2 pgood1 tg1 sw1 boost1 bg1 v in pgnd extv cc intv cc bg2 boost2 sw2 tg2 phasmd clkout pllin/mode run1 run2 sgnd ltc3858-2
ltc3858-2 32 38582f applications information figure 12. branch current waveforms r l1 d1 l1 sw1 r sense1 v out1 c out1 v in c in r in r l2 d2 bold lines indicate high switching current. keep lines to a minimum length. l2 sw2 38582 f12 r sense2 v out2 c out2
ltc3858-2 33 38582f typical applications efficiency vs output current start-up sw node waveforms figure 13. high efficiency dual 8.5v/3.3v step-down converter output current (a) 0.00001 0.0001 40 efficiency (%) 50 60 70 80 0.001 0.01 0.1 1 10 38582 f13b 30 20 10 0 90 100 v in = 12v burst mode operation v out = 8.5v v out = 3.3v 38582 f13c v out2 2v/div v out1 2v/div 20ms/div 38582 f13d sw1 5v/div sw2 5v/div 1s/div sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc v out2 run1 run2 freq ss2 v fb2 ss1 i lim phasmd clkout pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 1nf r b1 215k c out1 , c out2 : sanyo 10tpd150m l1: sumida cdep105-3r2m l2: sumida cdep105-7r2m mtop1, mtop2, mbot1, mbot2: vishay si7848dp c f1 15pf c ith1a 150pf c ss1 0.1f v out2 c ss2 0.1f c ith1 820pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 9v to 38v d2 ltc3858-2 l1 3.3h l2 7.2h r sense1 7m r sense2 10m mbot1 mtop2 mtop1 mbot2 38582 f13 100k 100k intv cc c out1 150f v out1 3.3v 5a v out2 8.5v 3a c in 22f c out2 150f r a1 68.1k r a2 44.2k r b2 422k c f2 39pf r ith1 15k 215k (optional tracking) 68.1k c2 1nf i th2 c ith2 680pf c ith2a 100pf r ith2 27k
ltc3858-2 34 38582f typical applications high efficiency dual 2.5v/3.3v step-down converter sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc run1 run2 freq ss2 v fb2 ss1 i lim phasmd clkout pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 1nf r b1 143k c out1 , c out2 : sanyo 10tpd150m l1: sumida cdep105-2r5 l2: sumida cdep105-3r2m mtop1, mtop2, mbot1, mbot2: vishay si7848dp c f1 22pf c ith1a 100pf c ss1 0.01f c ss2 0.01f c ith1 820pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 4v to 38v d2 ltc3858-2 l1 2.4h l2 3.2h r sense1 7m r sense2 7m mbot1 mtop2 mtop1 mbot2 38582 ta02 100k 100k intv cc c out1 150f v out1 2.5v 5a v out2 3.3v 5a c in 22f c out2 150f r a1 68.1k r a2 68.1k r b2 215k c f2 15pf r ith1 22k c2 1nf i th2 c ith2 820pf c ith2a 150pf r ith2 15k
ltc3858-2 35 38582f typical applications high efficiency dual 12v/5v step-down converter sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc v out1 run1 run2 freq ss2 v fb2 ss1 i lim phasmd clkout pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 1nf r b1 422k c out1 : kemet t525d476m016e035 c out2 : sanyo 10tpd150m l1: sumida cdep105-8r8m l2: sumida cdep105-4r3m mtop1, mtop2, mbot1, mbot2: vishay si7848dp c f1 33pf c ith1a 100pf c ss1 0.01f c ss2 0.01f c ith1 680pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 12.5v to 38v d2 ltc3858-2 l1 8.8h l2 4.3h r sense1 10m r sense2 7m mbot1 mtop2 mtop1 mbot2 38582 ta03 100k 100k intv cc c out1 47f v out1 12v 3a v out2 5v 5a c in 22f c out2 150f r a1 30.1k r a2 75k r b2 393k c f2 15pf r freq 60k r ith1 33k c2 1nf i th2 c ith2 680pf c ith2a 100pf r ith2 17k
ltc3858-2 36 38582f high efficiency dual 24v/5v step-down converter typical applications sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc v out2 run1 run2 freq ss2 v fb2 ss1 pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 1nf r b1 487k c out2 : sanyo 10tpd150m l1: sumida cdrh105r-220m l2: sumida cdep105-4r3m mtop1, mtop2, mbot1, mbot2: vishay si7848dp c f1 18pf c ith1a 100pf c ss1 0.01f c ss2 0.01f c ith1 680pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 28v to 38v d2 ltc3858-2 l1 22h l2 4.3h r sense1 25m r sense2 7m mbot1 mtop2 mtop1 mbot2 38582 ta04 100k 100k intv cc c out1 22f = 2 ceramic v out1 24v 1a v out2 5v 5a c in 22f c out2 150f r a1 16.9k r a2 75k r b2 392k c f2 15pf r freq 60k r ith1 46k c2 1nf i th2 c ith2 680pf c ith2a 100pf r ith2 17k i lim phasmd clkout
ltc3858-2 37 38582f high efficiency dual 1v/1.2v step-down converter typical applications sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc run1 run2 freq ss2 v fb2 ss1 i lim phasmd clkout pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 1nf r b1 28.7k c out1 , c out2 : sanyo 2r5tpe220m l1: sumida cdep105-0r4 l2: sumida cdep105-0r4 mtop1, mtop2: renesas rjk0305 mbot1, mbot2: renesas rjk0328 c f1 56pf c ith1a 200pf c ss1 0.01f c ss2 0.01f c ith1 1000pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 12v d2 ltc3858-2 l1 0.47h l2 0.47h r sense1 4m r sense2 4m mbot1 mtop2 mtop1 mbot2 38582 ta05 100k 100k intv cc c out1 220f = 2 v out1 1v 8a v out2 1.2v 8a c in 22f c out2 220f = 2 r a1 115k r a2 115k r b2 57.6k c f2 56pf r freq 60k r ith1 3.93k c2 1nf i th2 c ith2 1000pf c ith2a 200pf r ith2 3.93k
ltc3858-2 38 38582f high efficiency dual 1v/1.2v step-down converter with inductor dcr current sensing typical applications sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc run1 run2 freq ss2 v fb2 ss1 pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 0.1f r b1 28.7k c out1 , c out2 : sanyo 2r5tpe220m l1, l2: vishay ihl p2525czerr47m06 mtop1, mtop2: renesas rjk0305 mbot1, mbot2: renesas rjk0328 c f1 56pf c ith1a 200pf c ss1 0.01f c ss2 0.01f c ith1 1000pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 12v d2 ltc3858-2 l1 0.47h l2 0.47h mbot1 mtop2 mtop1 mbot2 38582 ta06 100k 100k r s1 1.18k r s2 1.18k intv cc c out1 220f = 2 v out1 1v 8a v out2 1.2v 8a c in 22f c out2 220f = 2 r a1 115k r a2 115k r b2 57.6k c f2 56pf r freq 65k r ith1 3.93k c2 0.1f i th2 c ith2 1000pf c ith2a 220pf r ith2 3.93k clkout phasmd i lim
ltc3858-2 39 38582f information furnished by linear technology corporation is believed to be accurate and reliable. however, no responsibility is assumed for its use. linear technology corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. package description uh package 32-lead plastic qfn (5mm 5mm) (reference ltc dwg # 05-08-1693 rev d) 5.00 p 0.10 (4 sides) note: 1. drawing proposed to be a jedec package outline m0-220 variation whhd-(x) (to be approved) 2. drawing not to scale 3. all dimensions are in millimeters 4. dimensions of exposed pad on bottom of package do not include mold flash. mold flash, if present, shall not exceed 0.20mm on any side 5. exposed pad shall be solder plated 6. shaded area is only a reference for pin 1 location on the top and bottom of package pin 1 top mark (note 6) 0.40 p 0.10 31 1 2 32 bottom viewexposed pad 3.50 ref (4-sides) 3.45 p 0.10 3.45 p 0.10 0.75 p 0.05 r = 0.115 typ 0.25 p 0.05 (uh32) qfn 0406 rev d 0.50 bsc 0.200 ref 0.00 C 0.05 0.70 p 0.05 3.50 ref (4 sides) 4.10 p 0.05 5.50 p 0.05 0.25 p 0.05 package outline 0.50 bsc recommended solder pad layout apply solder mask to areas that are not soldered pin 1 notch r = 0.30 typ or 0.35 s 45 o chamfer r = 0.05 typ 3.45 p 0.05 3.45 p 0.05
ltc3858-2 40 38582f linear technology corporation 1630 mccarthy blvd., milpitas, ca 95035-7417 (408) 432-1900 fax: (408) 434-0507 www.linear.com ? linear technology corporation 2010 lt 1110 ? printed in usa related parts typical application high efficiency 2-phase 12v/150w step-down converter part number description comments ltc3859 low i q , triple output buck/buck/boost synchronous dc/dc controller outputs (5v) remain in regulation through cold crank 2.5v v in 38v, v out(bucks) up to 24v, v out(boost) up to 60v, i q = 55a, ltc3868/ltc3868-1 low i q , dual output 2-phase synchronous step- down dc/dc controllers with 99% duty cycle phase-lockable fixed operating frequency 50khz to 900khz, 4v v in 24v, 0.8v v out 14v, i q = 170a ltc3857/ltc3857-1 low i q , dual output 2-phase synchronous step- down dc/dc controllers with 99% duty cycle phase-lockable fixed operating frequency 50khz to 900khz, 4v v in 38v, 0.8v v out 24v, i q = 50a, LTC3890/LTC3890-1 60v, low i q , dual 2-phase synchronous step-down dc/dc controller with 99% duty cycle phase-lockable fixed operating frequency 50khz to 900khz, 4v v in 60v, 0.8v v out 24v, i q = 50a, ltc3834/ltc3834-1 low i q , synchronous step-down dc/dc controllers phase-lockable fixed operating frequency 140khz to 650khz, 4v v in 36v, 0.8v v out 10v, i q = 30a, ltc3835/ltc3835-1 low i q , synchronous step-down dc/dc controllers phase-lockable fixed operating frequency 140khz to 650khz, 4v v in 36v, 0.8v v out 10v, i q = 80a, ltc3891 60v, low i q , synchronous step-down dc/dc controller with 99% duty cycle phase-lockable fixed operating frequency 50khz to 900khz, 4v v in 60v, 0.8v v out 24v, i q = 50a, ltc3824 low i q , high voltage dc/dc controller, 100% duty cycle selectable fixed 200khz to 600khz operating frequency 4v v in 60v, 0.8v v out v in , i q = 40a, msop-10e sense1 + sense1 C sense2 C sense2 + v fb1 i th1 sgnd extv cc v out run1 run2 freq ss2 ss1 i th1 v fb1 v fb2 ss1 i lim phasmd clkout pllin/mode pgood1 pgood2 bg1 sw1 boost1 tg1 v in intv cc pgnd tg2 bg2 boost2 sw2 c1 1nf r b1 698k c out1 , c out2 : sanyo 16tqc22m l1, l2: sumida cdep106-6rom mtop1, mtop2: infineon bsz097n04ls mbot1, mbot2: infineon bsz097n04ls c f1 10pf c ith1a 68pf c ss1 0.1f c ith1 3300pf c int 4.7f c b1 0.47f c b2 0.47f d1 v in 19v to 28v d2 ltc3858-2 l1 6h l2 6h r sense1 5m r sense2 5m mbot1 mtop2 mtop1 mbot2 38582 ta07 100k 100k intv cc c out1 22f 16v v out 12v 12.5a 10f 16v c in 10f 50v 10f 50v c out2 22f 16v 10f 16v r a1 49.9k r ith1 2.94k c2 1nf i th2

▲Up To Search▲

Price & Availability of LTC3890

	To Download LTC3890 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .